If you’re subscribed to my YouTube channel then you’ll already know that I recently uploaded a video on the making of my magnetic knife block from last year. If you’ve noticed this upload appear twice in your subscription feed then it’s because I have re-uploaded the same video – in the first edition, I was made aware (by several viewers who left comments) that there was an issue with the narration running out of sync and beyond the end of the video footage; prolonging the length with an additional minute of black screen.
This has been corrected in the second upload. I’d like to leave the original video in its place because it’s already received a number of interactions. What I realised was that I made a mistake in recording and positioning the segments of narration before a final edit of the individual scenes – let that be a lesson to any other YouTubers or video-uploaders out there! It seems as though the strips of narration are not attached to the video timeline and so, as that shifts, the audio remains where it was.
So, from now on, this is the kind of schedule I’ll be following when editing a video for uploading. It is a lengthy process and I like to save as many individual versions of the video in as many states as you see listed below:
1. Initial edit and trimming of scenes.
2. Adding transitions between scenes.
3. Playing through the video to check and increasing the play-speed of any scenes where appropriate.
4. Recording and adding the narration.
5. Adjusting the sound levels between scenes and narration before a final check and then, the uploading!
Thanks for reading and I hope you like it. 🙂
After tidying up my router table this morning and adding the final touches with the featherboard accessories (photos to follow in another post), I spent the afternoon machining up some timber for a small job (yes, timber – not dusty MDF!) and also set about making a pair of simple-but-effective setting jigs for the knives (blades) on my 6in wide CT150 surface planer (jointer).
Continue reading “Jointer Knife Setting Jig”
After recently installing this aluminium plate in to my newly-built router table, I’m now able to look back and review it; analysing its features and my impression of this product at this early stage.
Continue reading “Axminster Aluminium Insert Plate”
As mentioned briefly in my previous post, I recently purchased Veritas’ Small Blade Holder from Rutlands, which is designed to solve the common problem applying the right amount of pressure to a small blade or iron when sharpening or honing. I don’t know about you but, I’ve always struggled to get a good edge on spokeshave blades unless they’re crudely fitted in to a slot cut in to the end of a length of 2x2in, for example. So, I was waiting eagerly for this product to arrive; to see if it would solve all those other issues. Veritas are renown for producing top-quality goods with a hint of innovation and it’s claimed that these holders will fit in to a honing guide for repeat angles and accuracy…
Continue reading “Veritas Small Blade Holder”
Rare earth magnets are kind of the things that can have a million and one different uses in a woodworking ‘shop. You’ve probably seen them available from places like Axminster, generally sold in quantities no greater than ten. Once you’ve started using a few of them, you soon begin to realise just how beneficial they can be and that initial pack of ten doesn’t go very far at all. That’s why I’d advise you to take a look at some of the listings on eBay, where bulk packs of fifty or even one-hundred magnets can be purchased for a very reasonable sum of money. I recently stocked up on a quantity of 8mm and 10mm diameter magnets (5mm and 7mm thick, respectively) and I thought I take the time to show you what I’ve been using them for so far. Perhaps this will give you some ideas for your own workshop.
Continue reading “Can I Play with Magnets?”
This evening (or, late-afternoon, if you prefer…), the FURNISH Exhibition kicks off in Bristol. A few of us began setting up yesterday, without everyone else arriving around midday today. I had to unload my pieces in two trips, partly because my chair and the curved cabinet were both awaiting a final coat of polish! So, I’ve been in and got my space set up. As of 6pm, the punters will start rolling in…
Continue reading “FURNISH, Bristol – 8th-13th July 2010”