This video was uploaded very late on Saturday night. It might even have been close to midnight, as I remember waking up on the end of my bed (I must have fallen asleep prematurely) at 1.15am, to discover that I’d already received 3 likes and my first comment on YouTube! I’ve taken a lot of positives from this one since, as I’m almost now up to 20 Likes for this one video, while still under 200 views in total.
As I say in the beginning; it was my first attempt at a narration and clearly, it works very well. I was actually hoping that I could’ve cut the footage down to around 8 minutes for this but I’m satisfied with 11.30 and, according to the statistics and comments; so are the majority of the viewers so far.
Tomorrow night, I’m hoping to upload the jig-making add-on to this, where I show you how I made the jig for my mitre saw. Then, over the weekend, I’m aiming to have another small project for you to view.
At work today, I spent a lot of time thinking about how I haven’t done a video for over one month now; how much I want to make the most of what time I have left in my workshop; how I need to crack on and finish the mobile base I started for my table saw, weeks ago… All whilst banging nail after nail in to small sheets of wavy birch plywood!
So, I was home by 17.00 and, after briefly stopping in the bathroom, I grabbed my camera and headed straight out to the workshop! Evenings have been almost mild this week (even though forecasters are now forewarning the threat of snow to follow this weekend – just when we were opening our arms to welcome the spring!). In two hours, I managed to get the following filmed and also, I made some good progress on the mobile base, which I’ll share with you another time.
This is something that I originally intended to film and publish about a month ago during Get Woodworking Week… I also have a ‘Valentine’s Gift’ idea that I’d like to film at some point but, it looks like I’m going to sail straight past Mother’s Day with that one as well! This video’s all about cutting a tee-halving joint, which is a traditional form of lap-joint, between two pieces at 90°.
I hope you enjoy the video. I’m incredibly nervous and fast-talking infront of the camera but I welcome all and any comments people may have. It takes a good hour for me to upload a video of this length and I do now try to keep them brief… That also means compromising a little on the finished quality but then, I’m only using Windows Movie Maker, which is a free program.
If I was to use something paid-for (like Camtasia), would I able to experience faster upload speeds?
Ideally, I’d like to have one short video to upload once each week. In fact, from the video I’m sharing with you this evening, I could easily have cut a section from the end and published that under its own heading.
Along with rare earth magnets (as detailed in my previous post), I’m also beginning to realise that springs (particularly the compression-type) also have a place in the woodworking workshop.
Above, I’ve fitted a 75mm long compression spring between the two M16 nuts on the depth stop for my recently-purchased ED16B pillar drill. I’m sure I made it clear before that I was a little disappointed with this arrangement when I first purchased the machine. Finger-tight pressure between the two nuts was not enough when running the drill on one of the higher speeds – they always vibrate loose so, you have to use a spanner (or, preferably, two). But, with this spring (and a couple of M16 washers) now in place, that’s all in the past. Now, I can easily set the drilling depth without having to reach for a tool – my thanks go to Mike Garnham for this solution.
This monster’s been in my workshop for a few months now. In that time, I’ve been able to do just about everything with it – from cutting curves and shaping, to to forming lap joints and deep-ripping wide boards of hardwood. There isn’t much that I haven’t already done with it [I’ve even broken a blade and ripped the tyre off the top wheel!!] so, I think it’s about time I gave my verdict.
As mentioned in a recent post, Ian John is back in business trading under the name of Tuff Saws. I’ve been happily using a ½”x4tpi thin-kerf blade since December but today’s post is all about a “Fastcut” from the Supertuff range. I’ve been eager to try this one out since it arrived and, today, I even managed to shoot a couple of brief videos to show you how it performs.